50K Fan Celebration :: Ruched Ankles PegLegs Hack

April 23, 2017

Ahoy Pirates!

Today I’m going to show you how to add some ruching to the ankles of your PegLegs. This is a super easy way to amp up their cuteness factor and take them to the next level.

For this hack, I’ll be ruching using elastic. Depending on your preferences, you’ll need about 12″ of braided (non-roll) elastic. I used 1/2″, though you can also use 1/8″, if you’d prefer. You will also need matching thread.

1. The first thing you need to do is decide how long you want your line of ruching to be. For mine, I chose 5″.

2. You’ll need to add length to the pattern to accommodate the fabric the ruching will take up; you’ll add the same number you originally chose. So for me, the length to add was also 5″. And now the total ruched amount will be 10″.

3. Add the extra length at the capri cut line. To do this, cut your pattern on the capri line, add however many inches you chose earlier. I added 5″. Then cut out your leg pieces with this added length, and your choice of waistband. Your leggings will look crazy long – this is good!

4. I highly suggest hemming the bottom edge now, before ruching. It will be so much easier this way; I chose to do a faux blind hem with my serger. Or, let’s be real…if you’re not planning on hemming, then this doesn’t apply to you! 😉

5. Cut your elastic pieces. To determine the length, add 1″ to your original measurement. So I cut mine 6″.

6. Now, before you sew up the side seams, find the middle of the piece on the end, and mark it. Pin/clip your elastic in place in this place, right above your hem.

7. From the marked spot, measure up your total ruched amount, determined in step 2. My ruched amount was 10″, so I measured 10″ above my marked spot. Add a pin to this spot as well.

8. Now bring the other end of the elastic to the pin and pin it to the fabric. This is the spot which will be ruched.

9. You’ll be sewing the elastic to the fabric now, stretching as you sew. This can be a little tricky, so I advise you test this out on a scrap before sewing your actual ruched piece.

10. Using a slightly shorter zigzag stitch (my length was 1.8, you may also need to reduce the width as well, I used 2.5), start sewing at the end of your elastic. Don’t worry about pulling the elastic until you can grab the end of it from behind the presser foot. This should be about 1/2″ of stitching until you can grab it.

11. The trick now is to hold the elastic from the back while you also pull it from the front, as you are sewing (I couldn’t show this while also holding the camera to take this picture). 😉 This way, you can control it pretty well. I find it helpful to stretch the elastic before sewing, and then pin the middle part to the fabric. Now you can pull from the pin to the presser foot instead of from the very end. Once you get to the pin, then pull from end to end until you are finished sewing. Be sure to backstitch carefully. Don’t worry about making it absolutely perfect, because the ruching will bunch up quite a bit.

12. Now, assemble your PegLegs as usual…sewing the side seams, the waistband, etc. Good news is you’ve already hemmed! Or chosen not to…

That’s it – you’re done! Feel free to play around with different lengths of ruching as well, you may prefer more or less than me. Also, you can also ruche using elastic thread hand-wound in your bobbin. With this method, you’d also lengthen your pattern, and then sew a straight line however many inches you added. I don’t mind using elastic though, since I always have it on hand (not the case with elastic thread!).

Be sure to post your ruching hacks in our Facebook group so we can have all the “heart eyes” for your creations! 😍

~Elisabeth

We are celebrating reaching 50K fans in our Facebook group! To make it a party, our beloved PegLegs pattern just got an update AND some new add-ons. Before you go running to your machine to sew up your own leggings, make sure to read our PegLegs 101 blog post. This way, you’ll have all the the information you’ll need to make the perfect pair before you even cut into your gorgeous fabric.

But wait, there’s more! After any good party is an after-party. We are taking it one step further and sharing some easy hacks that’ll bring even more flavor to your favorite leggings pattern! We hope you check them out, make your new favorite pair of leggings, and know that we appreciate every single one of you amazing sewing guys and gals!

Here are our hacks / tutorials / latest tricks:

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

50K Fan Celebration :: Stirrup Pant PegLegs Hack

April 22, 2017

Written by Kelly Bailey (P4P Blog Contributor)

For this tutorial I will be showing you how to take the updated Patterns for Pirates Peg Leg pattern and hack it into a pair of leggings featuring the stylish yoga stirrups! Have you seen these store purchased versions in your gym classes, or maybe on Pinterest, or maybe you’ve been looking for a comfortable pattern for stirrup leggings to compliment a casual outfit? This simple hack is both comfortable and durable. Follow along with this tutorial and please share your results in the P4P sewing group!

Step One: Fabric

My first, and most important, advice is to choose your fabric wisely. This pattern is intended for 4-way stretch knit with at least 50% stretch. See Peg Leg 101 to review the way the fabric contents and stretch will affect your results. Not all knits are meant for leggings due to the degree of stretch this pattern requires. For all 3 of my versions I have used a brushed polyester spandex knit with varying weights. Athletic knits, such as supplex or heavy weight brushed poly, are the best option if you intent to vigorously work out in your finished garment.

Step Two: Stirrup Pattern Piece

Print out and assemble your Peg Leg pattern as normal, being sure to add or take away height as necessary for you. See Peg Leg 101 for more information on how, where and when this is necessary. The Peg Leg pattern is drafted for an average height of 5’5” and an inseam of 28”. This hack can be applied to both the “plain” version and the “color-blocked” versions. Beware that once you’ve sewn this up you will not be able to simply trim off length at the very end of construction as you would with the standard pattern. So be sure to make a traditional pair and know these height adjustments before attempting this hack.

Next cut out a paper rectangle measuring 7.5” x 4”. The 4” height fits my size 9 foot perfectly but you may need to add or remove a little bit to that measurement depending on your shoe size.

Step Three: Modifying the Peg Leg Pattern

If you’re modifying the “plain” version tape your rectangle to the ankle of your peg pattern as shown. Be sure to pay attention to the side you’re attaching the rectangle to. You want to line the edge of the stirrup rectangle with the FRONT side of the leg piece.

If your modifying one of the “color-blocked” versions line up and attach your stirrup rectangle with the edge of the FRONT pattern piece as pictured.

NOTE: You can switch up the top and middle color-block panel pieces and the pattern will still go together without issue if you are not attaching the pocket. If you do attach the pocket still, it would just sit lower on your leg. My charcoal and hot pink pair show what this swap looks like. My navy and seaglass version show the color-block panel assembly as instructed in the original pattern. I also chose to give a faux flatlock look to my pink version. Follow Alex’s decorative top stitching blog to get this look yourself!

Step Four: Cut Out Your Pieces & Assemble Color-block

Use your modified pattern to cut from your fabric all legging pieces. Add to this the addition of two 1.25” x width of ankle strips with the greatest stretch going with the longer length. Theses will be the bands that stretch around the heel of your foot. The width measurement will leave extra that will get trimmed off after attachment. For a size small I cut a 8″x 1.25″ sized heel band.

For the “plain version” make a cut in each leg piece, as shown in the image below, just to the center width of the leg. This is where you will attach the heel band.

For the “color-blocked” version you are going to sew together all color-block pieces as normal, creating two full leg pieces. You will need to pivot the seam 90 degrees to attach the stirrup to the ankle at the front of the leg. Be sure to only sew the stirrup to the halfway mark along the ankle (mid color-block). Leave the rest unattached so that you can sew the heel band in place.

Step Five: Sew Crotch Seams

Lay your fully assembled leg pieces right sides together on top of one another. Sew your crotch curves together.

Step Six: Attach Heel Bands

Press your heel bands wrong sides together lengthwise and then pin along the unfinished slit along ankle edge. Sew in place being sure to use a stretch stitch but not to stretch either the band or the leg piece.

Step Seven: Pin Inseam in Place

Start by pinning your crotch seams right sides together then go to the stirrup piece and start lining up inseams there. Work your way up the leg making sure to overlap the bands as shown in the photo below. Sew inseam together using stretch stitch. Trim off excess heel band.

Step Eight: Finishes

At this point you can attach your waistband using the directions in the patterns tutorial and then hem the bottom of the stirrups using a stretch stitch and your preferred hem width. Press.

All Done!

Try them on and enjoy. Keep your feet cozy whether in yoga class or sewing your next garment at home!

Here are our hacks / tutorials / latest tricks:

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

50K Fan Celebration :: Drawstring Waistband PegLegs Hack

April 21, 2017

Today I’m sharing a quick cute hack to your peg legs to add a drawstring to your waistband. I wear peglegs all year round and the drawstring changes up the look just a bit. Let’s get started.

First you sew your legs together as per the pattern.
Before we start the waistband we are going to make some markings. I am using a disappearing ink pen from my fabric store to mark mine. I folded my waistband in half to find the center and marked the center with my pen in a few spots. Next I found folded the fabric long sides together to mark where I wanted my buttonholes. I wanted my buttonholes in the middle of my waistband. Your waistband is 7 inchs wide so folded it is 3.5 inchs but the bottom .5 inch is your seam allowance therefore I measured 1.5 inchs down from the top fold and marked that as being the center right across the other mark that I had made. Now I have a little cross right marked.

3. Buttonholes can be a bit of a pain on knits so I added a little piece of interfacing on the back, I didn’t actually iron it on to my fabric I just wanted something to give it a bit of stability, a tear away stabilizer would also do the trick or you can iron on a piece of knit interfacing. I happened to have a bit of regular interfacing sitting here so that is what I used. I sewed the buttonholes on either side of my cross .25 inch from the center. I just did a really small buttonhole, it doesn’t need to be big cause you are just threading through some drawstring. Now for all those people that hate sewing buttonholes not to worry knits don’t fray so you can always just cut some little slits in the waistband if that is the option you choose make sure to iron on some knit interfacing thou, it would prevent the knit from stretching out while wearing them.

4. Once you have the buttonholes are done we are going to create a casing for your drawstring. First you are going to match the short sides of your waistband as the pattern directs and sew them together, fold the waist band in half and then your going to sew all the way around about .25 of an inch above the waistband and below the waistband. Now you can mark your lines here that you are going to sew but I’m a rebel and just went for it by sewing 1.25 inchs from my fold, for the second row of stitching I sewed .5 down from the first line I made. Once your casing is all done just attach the waistband to your legs as normal.

5. Now you just need to add your drawstring. I used 50 inchs of drawstring on the xxs size and I just tied off each end but you could certainly fold the ends over and hem the edges of your drawstring. I like to just put the drawstring around me and leave long tails and then insert it into my casing try it them on and you can always cut the drawstring shorter so start with a long piece and then cut them the length you like best. Remember you have to leave your drawstring fairly loose or you won’t be able to pull your leggings on! I figured this out while trying mine on! Another simple solution to use elastic for most of your drawstring, I would use 1/4 inch or 3/8 inch elastic. You could cut your elastic slightly shorter then your drawstring and then sew drawstring onto each end of your elastic and thread it through your casing, it would give you just a bit more give when pulling them on and off.

I hope you try adding some drawstring in your peglegs and don’t forget to show them off in our Facebook group! – Angela

Here are our hacks / tutorials / latest tricks:

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

50K Fan Celebration :: Decorative Topstitching PegLegs Hack

April 20, 2017

Are you guys loving this 50K celebration as much as we are? How many Peg Legs have you sewn already? Today on the blog I will show you how to take your Peg Legs up a notch with some decorative stitching. I will show you how to achieve the RTW look using your sewing machine, serger or coverstitch machine.

SEWING MACHINE

One way to add top stitching is by using your sewing machine and those stitches you never try 🙂 Most machines have at least a few decorative style stitches included. When you chose your favorite style, make sure that the density of the stitch is not too high and always lower the tension a bit. I used two different decorative stitches on the pockets so you can see how it would look.

I highly recommend placing a little bit of water soluble stabilizer between the back of the fabric and the dog feed. It will help prevent any fabric from being “eaten” by the machine.

Once you finished stitching simply tear away the stabilizer. Any residual will just disappear at the first contact with water.

COVERSTITCH MACHINE

My favorite way to add decorative stitching to athletic wear is by using a 3 needle reverse coverstitch. If you have a coverstitch machine that only has 2 needles you can certainly do that too. If you have wooly nylon or bulky nylon thread, use it in your looper!

Start by pressing and steaming your seams towards the outside of your middle colorblock. DO NOT SKIP this step! Pressing the seam before coverstitching AND after will yield the best looking decorative stitch.

In order to achieve the athletic wear topstitching you’ve seen in stores, place your fabric in the coverstich with the wrong side up. The right needle should be right in the ditch. Stitch slowly! If your coverstitch machine has a speed dial now is the best time to use it.

When you finish stitching give all your seams a good steam! Yes, I’ve said it before 🙂 but look how pretty it looks when you do.

SERGER

A third way to add decorative stitching is to use a flatlock stitch on your serger. I used a flat lock stitch to attach the waistband. Doing so not only makes the pegs look more like RTW ones but it also makes them feel nicer. As per its name the flat lock seam is flat so no bulky seam at the waistband.

Start by setting up your serger for a flat lock stitch. Make sure to read your manual because all machines are different. You will only be using your left needle. These are the settings I use but please make sure to always test out your machine with similar fabric as the one you’ll be using in your main project. The tension and stitch length will vary from fabric to fabric.

If you’d like to attach the waistband using this style stitch you can can put the waistband inside the pants this way the “back” will be showing or you can place the waistband outside the pants so the front will be showing.

I placed my waistband inside because I wanted the ladder stitch to show on the inside and the “zig zag” look on the outside.

There you have it..3 ways to add decorative stitching using your regular sewing machine or your serger or your coverstitch machine! I can’t wait to see your fabulous Peg Legs so be sure to post your creations in the group!

Here are our hacks / tutorials / latest tricks:

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

50K Fan Celebration :: Lace Waistband PegLegs Hack

April 19, 2017

Every once in awhile, our Facebook group gets hit with a picture of a trending item with the question “How can I make this?”. For a few months, a picture of a lace waistband was circulated and while we secretly worked on the Peg Legs update, we knew we had to add it to our hack lineup.

To achieve this look, we are going to eliminate the waistband piece, but in order to help keep them up, we will be increasing the rise and adding elastic at the top edge. You will also need wide stretch lace (we used lace between 5-6″ tall) and 1/4″-3/8″ elastic.

I wanted to keep the original mid-rise of the leggings but since we are eliminating the extra waistband piece, I cut on the high rise line and added about 0.25″ to accommodate the elastic. Once cut, assemble the legs as you normally would.

Cut your elastic the width of the waist of the Peg Legs. The Peg Legs already have negative ease (meaning, they are smaller than your body measurements and stretch to fit) so we do not need to cut the elastic smaller than the opening. This is just used as extra support to help keep them up.

Butt the ends of the elastic to one another, and using a zig-zag stitch, stitch, creating a circle. Stitch the elastic to the wrong side of the fabric using your favorite stretch stitch. If using a serger, do not cut any fabric off. The elastic should be measured at 1:1 with the top of the leggings so should not need to stretch to fit the opening.

To determine the size of the lace waistband, lay your lace on top of the leggings and cut them 1/2″ wider than the leggings on either side. Cut 2.

With right sides together, stitch each short end with a 1/2″ seam allowance to create a circle. Flip right side out.

With both right sides out, slip lace waistband over the leggings. I wanted to encase my elastic so chose to fold over the edge of the fabric as well. Top-stitch using your favorite stretch stitch around the top edge of the leggings. I did not stitch along the bottom edge of the lace. I used a brushed poly so the lace sort of “stuck” to the fabric when worn so found I did not need to stitch the bottom edge in place.

Here are our hacks / tutorials / latest tricks:

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

50K Fan Celebration :: PegLegs Update + Re-Release!

April 17, 2017

We are celebrating reaching 50K fans in our Facebook group! To say the least, it is unbelievable that I have added so many ladies into the tiny group it started from. I’m so honored to help each and every member learn a little more about sewing. It makes my heart so happy to see posts about first time sews and the community answering questions with nothing but a kind heart. I love the P4P group so much! So, we tried to think of something AMAZING to say thank you for supporting us! To make it a party, our beloved PegLegs pattern just got an update AND some new add-ons.

The Peg Legs original pattern has gotten more reviews and feedback than any other P4P pattern hands down! So, naturally we took that feedback and tweaked them slightly. We also updated them to include the newest features P4P offers: layers feature, as well as A0 and International print options. Just like before, we have four different length options (ankle, capri, bike and shortie). *If you already have the Peg Legs in your account you will simple need to redownload them to have the new updated files.

We’ve also added a different rise option, for those of you who like a little higher waist. You can choose from high AND low/mid rises for your perfect leggings fit. The low/mid rise is the same as the original peg legs.

Now to really bring the celebration up a notch– the Add Ons! But what do the add-ons include? So many things!
We are giving you color blocking options, pockets (in the waistband AND along the side panel), a contoured high waistband, and a gusset. All extra options that you can mix-match to your heart’s content.

And, for all of you gorgeous pregnant mommas: a maternity add-on! You can take the basic Peg Legs pattern and add an under belly, under belly v, or an over belly waistband for your new favorite maternity wear.

We also updated all the Freebies to NO CODES NEEDED. We loved having everyone join the FB group and amazing community it has built, but we want them to be easy for everyone to get their hands on too! So, we hope everyone will still join the support group as well as enjoy the ease of grabbing the freebies with no codes 🙂

Before you go running to your machine to sew up your own leggings, make sure to read our PegLegs 101 blog post. This way, you’ll have all the the information you’ll need to make the perfect pair before you even cut into your gorgeous fabric.

But wait, there’s more! After any good party is an after-party. We are taking it one step further and sharing some easy hacks that’ll bring even more flavor to your favorite leggings pattern!

We hope you check them out, make your new favorite pair of leggings, and know that we appreciate every single one of you amazing sewing guys and gals!

Here are our hacks / tutorials / latest tricks:

*****These will be made live as we post them throughout the next week! *****

Lace Waistband Alternative | Drawstring Waistband Tutorial
Exposed Elastic Waistband | Stirrup Pant Hack
Ruched Ankles Adjustment | Decorative Topstitching Tutorial
Ruched Side Panel Hack

Still want more?!?! Join us for our Peg Legs Sew-A-Long!

And of course one LAST thing to celebrate reaching 50.000 FB members is a SITE WIDE SALE! Enjoy 30%off your total purchase with coupon code: “50ksale” now through April 25th (ends 11:59PM the night of the 25th US Central Time Zone). *Bundle Discounts will not work with site wide sale code.

Thank you for giving this little work from home mama the chance to do what she loves! I hope each and everyone of you enjoys the updated pattern, the add ons, the hacks, the sew-a-long and the site wide sale 🙂

<3 Judy

Spring Mini Capsule Winners

April 11, 2017

Wow, we have LOVED seeing everyone’s mini capsules they made during the contest! It was amazing to see so many wonderful outfits. Plus doesn’t it feel great being ready for Spring?? If you haven’t finished your mini capsule yet, please continue to work on it and post when you can. We would still love to see what you create 🙂 We enjoyed it so much, we will be hosting another capsule contest in the Fall. Now on to the winners! Winners will be tagged on Instagram and/or Facebook and simply need to email patternsforpirates@gmail.com AND madeformermaids@live.com for their pattern prizes. Fabric and grand prizes just email M4M. Drumroll please…

5 Winners each get to choose 1 pattern of choice from EACH M4M & P4P:

Alicia Zylstra from our FB groups.

@faerieflings from Instagram.

Debbie Brennan‎‎ from our FB groups.

@sillybugzboutique from Instagram.

Sara Marie from our FB groups.

3 Winners each get to choose 3 patterns from EACH P4P & M4M:

@sewing4sanity on Instagram.

Alyssa Arthur from our FB groups.

Amanda Massicotte Jones from our FB groups.

1 Winner for a $50 store credit to Sincerely Rylee ‎‎Fabric Shop:

@songofgrace on Instagram.

1 Winner for a $50 store credit to Pretty Posh Prints:

Cherie Williamson from our FB groups.‎

1 Winner for a $100 store credit to Knitpop:

Abby Mercer Eason from our FB groups.

GRAND PRIZE WINNER with their choice of a Brother Coverstitch Machine or $100 Joann Fabric Gift Card:

Nicole Joyce from our FB groups.

CONGRATS to all the winners!! Thank you so much again to our sponsors and everyone who participated! If you blogged about your capsule sewing, please leave a link in the comment section below so we can check it out.

Favorite Tee | Easy Pattern Hacks

April 11, 2017

Lace Up V-Neck:

As if the Favorite Tee was not amazing enough, we have a few easy hacks for it that will make you want to sew even more of them. The first time I saw a lace up V-neck shirt on Pinterest I knew I had to make myself one so I will show you how easy it is to get the look by using the Favorite Tee pattern. You will need the pattern printed and cut in your size (use the V neck option), a little bit of interfacing, 10 grommets and some cord.

Favorite Tee dress option (lengthen 1.5″ in the front and unhemmed)

Start by adding some tricot or light weight interfacing to the V neck band. Cut 2 strips of interfacing about 7 inches long by the width of the band. Cut out the V at one end and iron the interfacing to the neckband.

Sew the shirt or dress as per the pattern tutorial. I chose the dress because you know…one can never have too many dresses. You can certainly do this neckline with either one of the shirt length too. You will now need to mark the grommets location.

You can measure about one inch up on each side of the V band starting with the front center seam. Mark that spot. Keep adding a mark every one inch up on each side. I used 5 grommets on each side.

There are different size and color eyelets that you can use. I went with a brown/copper-ish finish for mine because I liked how it looked against the marble fabric.

ohhh the choices 🙂

Follow the manufacture instructions for adding the eyelets. I know there are more expensive devices out there but I am very pleased with my $1.50 Dritz eyelet tool so that’s what I used.

For a more edgy look you can make a faux leather binding and thread it through the eyelets.

You are almost done. All you have to do now is lace up the neckband with a cord. You can use parachute cord, or faux suede cord like I used for my final pics or you can make your own. Tadah! You have just created your very own Pinterest worthy lace up Vneck shirt or dress.

Favorite Tee dress length (1.5″ longer in the front than the pattern and not hemmed)

Curved Hem Lace Insert:

Adding lace to your finished garments is a fun way to add some extra sweet details. You can use a lace applique, or in this instance, I used a scalloped edge mesh lace. I chose the curved hem but you could use the other side split hem options if you’d prefer. Print, cut and assemble your pattern as usual. I wanted the curved hem to start a little higher on my hip so adjusted the length of the side seam. I stopped about 6″ from the bottom of the side seam.

Since I stopped higher than the original side seam, my curve ended up looking a little funky, so I trimmed the edges to make a nice clean curve.

Hem using your fabric stretch stitch. (Need some tips on hemming a curved hem? Check out Alex’s post HERE)

Next, open up your side seam and place your applique right side up to the wrong side of your main fabric. Position as you wish and top-stitch in place. *Note – be sure to measure your pattern piece from the curved hem line to side seam and make the applique at it’s widest point a similar measurement (near the bottom hem). Otherwise, you may loose some ease at the hip.

Trim the applique or fabric if needed.

High Side Split Hem:

The side split hem for both shirt and tunic lengths is a fun detail on it’s own, but we thought we’d take it up a notch (no pun intended 😉 ) and make those slits sky high. Ok, so maybe not that high but we did take them up quite a bit. Using the average 8″ side waist measurement (based on a 5’5″ frame), construct your pattern as instructed but stop your side seam stitch at 8″ below the armpit. Finish the side split as noted in the pattern. Easy Peasy and no added steps or items needed!

This pairs perfectly with our Cross my Heart Cami to show off those layers.

Or, leave it un-layered and open with a high waist Pirate Pencil Skirt or some skinnies. Either way, you’re sure to be on trend.

Convinced you need the pattern yet? The Favorite Tee is loaded with options and these simple hacks/mods give you that little extra to start filling up your closet without the worry of having too many duplicates. I know they’re our new Favorite Tee 😉

Favorite Tee | New Pattern Release!

April 11, 2017

After Judy teased you about a million times on Instagram with her pre-test versions of the Favorite Tee, we are finally going to give the people what they want.
No more teasers, it can be yours for keeps! And guess what? We made it in youth sizes too. Wahoo!

Here they are, your next most-sewn item: Favorite Tee (women’s) and Fav Tee (youth)

Both tees come packed full of options. The women’s Favorite Tee is drafted for sizes XXS – Plus 3X. There are a whopping FIVE hem options (shirt with side vent, tunic with side vent, banded knot tie hem, curved tunic length and curved dress length). There are THREE sleeve lengths included (short, 3/4 and long) and even TWO options for neck finishes (scoop or vneck).

**Want to learn more about how to measure yourself for this pattern? We’ve got you covered with an in-depth blog HERE.

The youth Fav Tee is drafted for sizes 3 months – 14 Youth. It features nearly all of the same options as the women’s version with FOUR hem options (shirt with side vent, tunic with side vent, banded knot tie hem, and curved dress length), THREE sleeve lengths (short, 3/4 and long) and TWO neckline options (scoop and vneck).

Ready to see what those options look like? Let’s do it!

THREE SLEEVE OPTIONS

SIDE VENT HEM

BANDED KNOT TIE HEM

CURVED TUNIC

CURVED DRESS

SCOOP NECK

VNECK

Ready to grab the patterns for yourself and start sewing?

Favorite Tee (women) | Fav Tee (youth) | Favorite Bundle (women + youth)

Need a little more inspiration? Head over to our Facebook Group and check out the tester albums. They are packed full of fabulous tester photos!
You can find the Favorite Tee album HERE, and the Fav Tee album HERE.

Happy Sewing!

Spring Mini Capsule

April 10, 2017

We’re rounding out our Spring Mini Capsule Contest that we partnered with Made for Mermaids and I’m here to show you the two I got finished! (I wanted to make four…two got completed 😉 )

Katy , Alex, and Roberta all shared theirs as well!

I finished up my Little Guy’s spring capsule quick! This totally gave me false hope of finishing all of them lol! I did mostly tees and shorts since our spring gets pretty hot here in the south. Here was my plan for him. I ended up leaving the yo-ho henley off for another raglan and the Lumberjack for a muscle tank. I also didn’t quite make it to any undies…but he really needed the shorts and tees more anyways! I switched out the joggers for the Cpt. Comfort jeans after finding some adorable striped denim that needed to be used.

I did 3 pairs of Pirate Playground Pants in the shorts length option.

These are a french terry with inseam pockets. I added some top-stitching to the pockets as well.

Another french terry pair here with inseam pockets and I added a little stripe down the side in the wrong side of the french terry.

And yet another french terry 😉 Can you tell my favorite fabric for the Pirate Playground Pants yet? These are the patch pocket option I added a little band to the pocket with the wrong side of the french terry.

One pair of Cpt. Comfort Jeans that I modified to a shorts length in a striped denim.

And one pair of Swashbuckler Swim Trunks. I still need to find the perfect drawstring for these!

Tops I did a three Jolly Roger Raglans in short sleeves. Two basic tees in cotton jerseys and one in swim fabric as a rash guard!

I added a Wingman Shirt in a cotton spandex.

And a Muscle Tank too.

We had fun with the silhouette machine and added a few of his favorite things to the plain ones. The graphic ones took Mama a LOOOOONG time to get drawn out, but Little Guy is over the moon with them so I guess the time was worth it 😉

They can mix and match a bit and now he’s ready for that warm weather! <3 I loved this little challenge and contest so much I told Megan we’ll need to do another in the Fall!

My Little Guy isn’t one for modeling much- so here are a few shots of them on a super silly boy!

I also snuck in another mini capsule for a baby shower gift! Hers didn’t mix and match quite as well as a traditional capsule should…but I still thought it was a great little set 🙂

For bottoms I used the Baby Bear Joggers with yoga waistband and cuff options. As well as some quickly drafted size 3 month leggings (as I called Megan complaining her Bonny’s didn’t go down to a small enough baby size 😉 )

I did 3 tops for her.

A Heart Breaker Cami in the plain option.

A Sugar Pie in short sleeves and curved tunic hem option. I added a cute little vinyl as well.

And a tiny Me Hearties in short sleeve and peplum options. I finished all the edges with a little scallop elastic.

For her layering pieces I did two Butterfly Cardigans.

One in tunic length with tall bands in a ribbed knit.

And one is a very lightweight sweater knit in tunic length and short bands.

I added in two little headbands using M4M knit headband and a little tiny hat too 🙂

Although you can mix and match a bit I paired them together for a few photos of my favorite outfit pairings! <3

The teeny tiny capsule was oh so cute to make and I think mama to be enjoyed it too!

We have absolutely loved seeing everyone’s mini capsules for this contest. I think it must go down as one of my very favorite contests we’ve done! Don’t miss out on the rest of the capsules that were shared here: Katy , Alex and Roberta.

We will be announcing the winner tomorrow!

5 Winners each get to choose 1 pattern of choice from EACH M4M & P4P:

3 Winners each get to choose 3 patterns from EACH P4P & M4M:

1 Winner for a $50 store credit to Sincerely Rylee ‎‎Fabric Shop:

1 Winner for a $50 store credit to Pretty Posh Prints:

1 Winner for a $100 store credit to Knitpop:

GRAND PRIZE WINNER with their choice of a Brother Coverstitch Machine or $100 Joann Fabric Gift Card:

connect with me