Patterns for Pirates

P4P stylish, modern, wearable patterns

2019 Holiday Freebies :: Festive Fabric Trees

Woohoo!  We are rolling into another day of our 2019 Holiday Freebies!  Get ready to make a million of these cuties…they’re really fun to make and are fabulous scrap busters.  Our testers just kept making more and more for their own homes, teacher gifts, and to fill their craft booths this holiday season.

Let’s get to making some happy little trees!

Grab your “FESTIVE FABRIC TREES” pattern pieces here!

Fabric Requirements (based upon 44″ quilting cottons):

Prep your pieces.  You will need four total tree pieces for one tree.

Place two of the pieces, right sides together.

Sew around outer edge.  Only sew an inch or two along the bottom curve, on both sides, to leave space for turning and adding the fiber fill.

Clip as close as you can to the seam allowance without going through it, and trim points.  This will allow for sharper points.

Turn right sides out and press, making sure to press under the seam allowance.  **Repeat with remaining pieces.

Press one of the sets in half, to create your guide line for sewing in the next step.

Align both sets on top of each other, keeping the one that you pressed on top.

Sew a line straight down the middle of all layers.

Fill all four openings with poly fill.

Hand stitch the openings shut on the bottom, using your favorite stitch.

You’re finished!  Sit back, enjoy your adorable new tree….and then go make a hundred more!  Here are a couple of cute ones from our testers!

As always, we love when you share what you’ve made with us.  Head over to the Patterns for Pirates Facebook group and show off the fabulous Festive Fabric Trees that you’ve managed to make from our freebie pattern!  Happy Holidays, friends!

2018 Holiday Freebies :: Critter Clutch

Welcome back to the second day of our P4P Holiday Freebies 2018!  I’m not sure I can even handle the excitement I have over today’s free pattern.  I am so happy to have this idea out of my head and finally in pattern form, to share with all of you.  AND FOR FREE!

These Critter Clutches are simply adorable!  They take minimal amounts of fabric, with not too much time involved in it.  The hardest part is deciding which version to do first: Unicorn, Reindeer or Fox??!!

You will need:
— Critter Clutch pattern pieces + Eye Digital Designs for HTV (found HERE)
— 1/2 yard main fabric, 1/2 yard lining fabric
— Fusible Fleece: I like Pellon 987F (aff link)
— Buttons / Snaps / Velcro for eyes and closures

Recommended fabrics: quilting cotton, kona cotton, flannel, etc.

Cut out all pieces needed for your corresponding bag.

Prepping the Strap:

Cut 3″ long x 34″ wide strip of fabric.
**Note: Depending if you or the recipient will be wearing it cross body or straight down from one shoulder, you may want to adjust the width of this piece to your liking.

1. Fold in half, with long edges touching, wrong sides together. Press.
2. + 3. Open up, and fold each long edge into the crease you just created.
4. Fold, completely enclosing the raw edges.

Edge stitch along both long edges. Set aside.  Finished width: 3/4″.

Horn / Ear / Antler / Nose Pieces: 

*Tip: I added fusible fleece to these pieces to help them stand up better.  Some of our testers opted to fill them with a small amount of fiberfil.  Either way works!

Right sides together, sew along the outer edges using 1/4″ seam allowance. Leave the bottom open for turning.

Clip corners and allowance before turning to get a crisper edge.  Topstitch if desired.

I like to get a little funky with the unicorn horn and add some decorative stitches to it.  This also helps the horn’s stiffness.

Apply Interfacing:

Carefully trim away 1/4″ from each interfacing piece, to allow for easier turning.

Following the instructions from the manufacturer, apply interfacing to these pieces:

  • Front Main Piece
  • Main Gussett

Eyes + Closures:

I personally like to add the eyes and velcro / snaps to the front main piece before we assemble the bag.  It allows for all of the stitching or snaps to be enclosed inside of the bags, and it’s a lot easier to apply HTV to a flat surface.  You can wait until the end if you’d like!

The Fox and Reindeer’s eyes need to be a little more wide set.  And the Unicorn’s eyes work best if you apply them closer to the bottom of the bag front.

Velcro / button placement on front main piece:

  • Unicorn / Plain Bag: 2″ from the top, centered (4.5″ from either side)
  • Fox / Reindeer: 2″ from the bottom, centered

Velcro / button placement on Back Lining piece:

  • Unicorn / Plain Bag: 2″ from the top, centered (4.5″ from either side)
  • Fox / Reindeer: 1.5″ from the bottom, centered

REINDEER ONLY:

1″ from the top edge, pin and baste ears in place using 1/8″ seam allowance.

Back Main Assembly:

UNICORN ONLY: Take back main piece and mark the center along the top, straight edge.  Mark center of horn piece.

Right sides together, align and pin/clip horn in place.

Place ears on either side of horn.  **Be sure not to go outside of your seam allowance on the outer edges, or you’ll have trouble turning your bag because the ears will be stuck in the outer edges.

FOX and REINDEER ONLY:

Right sides together, place ears and antlers (not pictured) 1″ from the outer edge.

ALL ANIMAL BAGS:

Place top piece, right sides together. Stitch with 1/4″ seam allowance.

Press open, with horn, antlers and/or ears pressed toward top and seam allowance pressed down.

Follow the manufacturer directions and iron your fusible interfacing onto the back side of the back main piece.

Attaching the Gusset:

Mark middle bottom of back piece and middle of both long edges of outer gusset piece.

Right sides together, ease gusset around bottom edge of back piece.  Sew using 1/4″ seam allowance.

Repeat for front main piece, attaching right sides together to other edge of gusset.

Repeat for lining pieces. Only this time, leave 4-5″ gap in one of the lining curves, to allow for turning.

Using 1/4″ allowance, baste straps, centered, on side gusset pieces. 

Final Assembly:

With the lining piece right sides out and the main, outer bag piece right sides out, slide the lining inside and align entire top edge.

Sew with 1/4″ seam allowance. Clip all edges and curves for cleaner turning.

Locate the opening you’d left in the lining.

Turn bag right-side-out through opening.

Pin and sew the opening in the lining closed, using your favorite blind or ladder stitch.

Press bag.  Topstitch around top edge if desired.

Reindeer Nose:

Align the nose at the very bottom of the front flap piece.  Top stitch the entire circle, catching the flap in your stitches and affixing the nose to the flap piece.

YOU’RE FINISHED!  DO A HAPPY DANCE!

In case you needed it, here is some inspiration for the different designs sewn up by our amazing testers!

UNICORN:

REINDEER

FOX

PLAIN

I hope you love these little cuties as much as I do.  Don’t forget to share your finished projects in the Patterns for Pirates Facebook Group!  Happy Holidays, friends!

2018 Holiday Freebies :: Infinity Scarf with Hidden Zipper Pocket

Happy December, friends!!  It is my pleasure to be back again this year with an entire week of goodies for you.  AND THEY ARE ALL FREE!  That’s right, you are about to embark on a five day journey of free sewing patterns and tutorials.  I’m excited to get started!

Today’s freebie is a twist on a classic infinity scarf…we added a hidden, zippered pocket to it!  It’s a perfect little space to store your phone, keys, or anything that you’d like to carry with you but don’t want to need a purse or extra hand for. It’s a super quick sew and is at the top of my gift-giving list this holiday season.

Let’s get started!

Fabric Requirements: 2 yards of knit, flannel, or a light-weight woven.

You will need:
— Main Scarf Piece: 28″ W x 72″ L (can be woven or knit. If using a knit, you may need small strips of stabilizer where you’re attaching your zipper)
— 2 pocket pieces: 9″ W x 7″ L
— 9″ Zipper **You can make the pocket bigger / smaller by adjusting the size width of your pocket pieces to match the length of your zipper.

1.) With your main fabric laying RIGHT SIDE UP, lay your zipper FACING DOWNWARDS, 5″ from the edge of your fabric, along one of the long edges.

2.) Sandwich your zipper by laying a pocket piece on top, RIGHT SIDE DOWN.

3.) Pin/clip and sew along edge, using a zipper foot to get as close to zipper as you can.

4.) Flip your pocket piece up and away from the main fabric.

5.) Fold your pocket piece under the main fabric (their wrong sides should be touching now).

6.) Fold main fabric together, matching the long sides to each other.

7.) Making sure you’re still 5″ from the short edge, align the unsewn side of the zipper to the opposite long edge of your fabric. Once again, your zipper should be FACE DOWN.

8.) Sandwich your zipper by laying your other pocket piece on top, RIGHT SIDE DOWN.

9.) Pin/clip and sew along edge.

10.) For easier sewing on the next step, I like to unzip my zipper a bit, to get the pull out of the way.

11.) With fabric still RIGHT SIDES TOGETHER, sew with 1/2″ seam allowance along long edges, and outer edges of pocket.

12.) This step might feel a little tricky, but it’s really not! You’re going to want to keep your fabric inside out, while folding it in half to still have right sides together, and the short edges meeting each other. I find it easiest to stick my arm all the way inside, grabbing the opposite short end, and then pulling it toward me from the inside, being careful not to twist it. Align the short edges to each other.

13.) Stitch the raw edges together with 1/2″ seam allowance, leaving a 4-5″ opening for turning.

14.) Turn scarf right side out, pulling the entirety of the fabric through the opening you created in the last step.

15.) Pin and close up the opening with a blind stitch. You’re finished!

Here’s a little inspiration from our fabulous group of testers, in case you needed it.

As always, we love when you share what you’ve made with us.  Head over to the Patterns for Pirates Facebook group and show off the fabulous Infinity Scarf that you’ve managed to make from our freebie pattern!  Happy Holidays, friends!

**Since there was such a high amount of requests for a video tutorial, here you go!

2017 Holiday Freebies: Easy Button Cowl

I’m back to gift you the final item for our 2017 Holiday Freebies!  Have you had fun with us so far this week?

In case you’ve missed the last four days, go take a look: Slouchy Headwarmer / Emoji Pillows / Clothing Size Tags / Camera Strap

On the last day of our freebies, we are sharing how to make this super cute, quick, and easy Button Cowl.  We’ve even got two ways for you to wear it.  Are you ready?  Let’s get to it!

 

Materials needed:

  • 2 – 26″ wide x 6″ long pieces of fabric (can be flannel, fleece, sweatshirt fabric, etc. Really anything will work, but obviously the cozier the better.)
  • 2 buttons / snaps
  • Coordinating thread

With fabrics right sides together, stitch around entire outside using 1/2″ seam allowance. Leave 3″ opening for turning.

Trim away bulk, making sure not to snip through seams.

Turn right-sides-out, through the opening.

Tuck in your seam allowance, press.

Top stitch along entire outer edge, making sure to catch your opening in there.

There are two ways you can add buttons/snaps to the cowl to create different ways to wear them.  I created an easy diagram to help you with placement for your buttons and button holes, depending on the style you’re wanting for your cowl.

Here’s a quick peek at what some of our testers made for themselves with this pattern:

As always, we would love if you shared your creations with us!  Head over to the Patterns for Pirates Facebook Group and show us what you made!  Happy Holidays, friends!

2017 Holiday Freebies: DIY Camera Strap

What?  We are on day four of the 2017 Holiday Freebies already?  I hope you’re having as much fun as I am!  If you need to back and review the past three days, I can wait!

Here are some links: Slouchy Headwarmer / Emoji Pillows / Clothing Size Tags

Now that we’ve covered that, let’s get to today’s free pattern!  Sewing and photography seem to go hand-in-hand more often, because we want to share what we’ve made with our sewing community!  Why not sew yourself a sweet little strap to wear while you’re using that camera of yours?  It’s super easy to do and way more fun than using what came with your camera originally.  Let’s get to it!

Prep your pieces, you will need:

  • Pattern Piece for Vinyl Ends
  • 36″ L x 12″ W Quilting Cotton
  • 2 – 12″ cuts of nylon webbing (1/2″ or 3/8″ both work) — I used THIS
  • 2 – 1/2″ or 3/8″ sliding adjusters — I used THESE black versions as well as THESE fun colored ones!
  • 36 L x 3″ W Fusible Fleece Interfacing
  • Small scraps of Vinyl/Pleather

**If you can’t find the nylon webbing / sliding adjusters in your local fabric store, a quick trick is to buy a small dog collar from the dollar store.  They tend to have the right width strap, and usually include the adjuster on it as well.

Important: The ends of nylon wedding need to be heat sealed to prevent fraying.  Make sure to do this before sewing it to your strap pieces!

**If your fabric is directional, you will want to cut two pieces for your strap and then stitch them together. Cut two 18.5″ x 12″ pieces from your quilting cotton.

For directional fabric, place your pieces right sides together, and sew along the short edge, using 1/2″ seam allowance.

Press open your seam.

For all straps: Fold your main fabric wrong sides together, meeting the long edges to one another. Press.

Open up your piece and fold one of the raw edges toward the middle crease you just made.

Repeat with the second raw edge. Press.

If you open your piece, you’ll now have 3 creases, spread evenly across four total sections.

On one of the middle sections, following the directions provided by the manufacturer, iron your fusible fleece to your strap piece.

We will be refolding the strap in the same method as before. Take one of the raw edges and fold it toward the middle crease.

Repeat with other raw edge.

Fold along middle crease, meeting both folded edges. All of your raw edges will be fully enclosed now.

Press, press, press.

I like to clip/pin my outer edges together, to make sure they’ll align properly when I go to stitch them. Straight stitch along the entire edge you just pinned, getting as close to the edge as you can.

This part is up to you, and how fancy you want to get with your quilting. I like to run an edge stitch along the other long edge. And then three even lines across the rest of the strap. You can stitch as much or as little as you’d like!

Take your nylon strap and overlap it 1.5″ from the edge of your strap, aligning it directly in the center of the strap.

Pin and repeat for the opposite end.

Using a wide zig zag stitch, secure your nylon strap to the end.

For the vinyl pieces, I recommend to only cut one actual piece — and to have an oversized rectangle for the other. It’s easier than trying to get them to line up perfectly. Especially since vinyl can be fussy to topstitch.

I like to run a line of fabric glue at the top of the vinyl backside. It helps keep it in place when sewing.

Two inches up from the bottom of your strap piece, lay out one of the vinyl pieces. The vinyl should be slightly wider than your strap.

Flip over your strap.

Throw another line of glue on the edge of your vinyl square.

Place it 2″ up from the bottom of your strap.

Flip your piece back over and stitch your vinyl on. This is the path I take and it allows for a continuous stitch. You can take whatever path you want. 

I HIGHLY recommend using a teflon foot for this. Vinyl can be a huge brat. I know they carry them at JoAnn Fabrics, or you can snag one on Amazon.

Finished stitches.

Trim the vinyl to match your other pieces.

Be careful not to cut off your nylon strap. Just tuck it out of the way when you’re trimming.

Take your slider.

Slide it onto your strap.

Put the cord in from the bottom-up on your camera.

Give yourself a little slack.

Run the cord back through the bottom and secure the strap to your camera. Easy peasy!

 

I am SO EXCITED to see your new, stylin’ camera straps!  I’ve been using my me-made strap for years now (so has my hubby) and we get compliments on it all the time.  I’m betting you will too!  Please, if you do make one for yourself, share it with us in the Patterns for Pirates Facebook Group!

**Also, as a quick note, there are some affiliate links scattered within this post.  I make a small commission for purchases made through those links, but I only link products that I’ve used and actually recommend myself.

2017 Holiday Freebies :: Size Tags

We are back for more fun with day three of our 2017 Holiday Freebies!  (In case you missed the last two…check out our Slouchy Headwarmer + Emoji Pillows and then come right back!)

One of the only complaints I get in my household about the handmade clothes I make for my husband and son are that there aren’t tags.  Apparently it’s not as easy for everyone as it is for us to find the back of your shirt!  We are helping to change that with these cute clothing size tags, so now the only complaint should be that they don’t have enough of your handiwork hanging in their closets!

I made the “THIS IS THE BACK” tags for my own family’s use a while back and thought I might share it with my P4P friends!  And then we couldn’t leave you with just one (kinda snarky) design, so I whipped up two more styles to go along with it.  I think a favorite with our holiday help were the “Size: Unique” set.  Now you can label your clothing properly with things like: beautiful, sassy, strong, healthy, etc.  Kinda fun, right?

You can go pick up your copy of these designs right HERE.

Don’t own a die cutting machine like a Silhouette or Cricut?  No sweat!  We have included an extra file type (PNG) that will allow you to work with the designs however you’d like.  We even had someone print on fabric using their at-home printer and sewed the labels in that way.  Pretty clever, huh?

Here are some other ideas:

— Go old school and use an iron on transfer paper and your at-home printer.
— Use Heat Transfer Vinyl and your die cutter.
— Try your hand at Freezer Paper Stenciling.  (Dana from Made Everyday has a great tutorial HERE.)

And just as a handy little tip from someone who has been using tags like these for a while now, I like to cut a bunch of tags on my Silhouette, weed them, lay them on a piece of parchment paper and then cut them out. That way, they’re ready to go when I need them. No fuss!

As always, we love to see what you make from our goodies!  Please feel free to share with us over in the Patterns for Pirates Facebook Group!  And make sure to come back tomorrow to see what else we’ve cooked up this week for you!  Happy Holidays, Friends!

2017 Holiday Freebies :: Emoji Pillows

We are back for Day 2 of our 2017 Holiday Freebies!  (In case you missed yesterday’s, head here to learn how to make this awesome Slouchy Headwarmer!)

I don’t think you’ve braced yourselves enough for today’s freebie, though.  If you’ve got a kiddo (or a kid at heart!) on your holiday gift list, we just might have the perfect solution for you: EMOJI PILLOWS!

These pillows come out to be 12″ tall.
You will need:
— Emoji Pillow pattern pieces (found HERE)
— small amounts of yellow, red, black, and/or brown fabrics.
— fiberfill (aff link)

Recommended fabrics: flannel, fleece, sweatshirt fleece, kona cotton, quilting cotton, etc.

**Optional, but highly recommended for woven fabrics that can fray (affiliate links):
— If you plan on finishing your face pieces with stitching: Wonder Under Sewable or Heat n Bond Iron-On Sewable Adhesive, etc. are great because they are machine safe and won’t gunk up your needles.
— If you don’t plan on stitching the face pieces to the pillows: Heat ‘N Bond Ultra Hold Iron-On Adhesive, etc. are better since they tend to have a stronger hold.  You just don’t want to stitch through those!

Heart Eye Emoji Pillow:

  • Cut 2 Heart Eyes
  • Cut 1 Mouth
  • Cut 2 Main Pillow Pieces

Poop Emoji Pillow:

  • Cut 2 Outer Eyes
  • Cut 2 Inner Eyes
  • Cut 1 Mouth
  • Cut 2 Main Pillow Pieces

Sleepy Emoji Pillow:

  • Cut 2 Sleepy Eyes
  • Cut 1 Mouth
  • Cut 3 Z’s
  • Cut 2 Main Pillow Pieces

Sunglasses Emoji Pillow

  • Cut 1 Sunglasses
  • Cut 1 Mouth
  • Cut 2 Main Pillow Pieces

ALL MAIN PILLOW PIECES HAVE 1/4″ SEAM ALLOWANCE.
**THERE ARE NO SEAM ALLOWANCES ON THE FACE PIECES, AS THOSE ARE ALL APPLIQUED OR IRONED ON.

Iron pieces to interfacing according to instructions.  If using an iron-on method only, apply your face pieces directly to one main pillow piece.

If using the applique method, pin your face pieces into place and zig zag stitch around pieces, securing them to the pillow piece.

Lay your main pillow body right sides together.

Sew around entire outside, using 1/4″ seam allowance. Leave 3″ opening at the bottom for turning.

Without clipping through seam, trim and clip corners for easy turning.

Turn pillow right-side-out, through opening you’d left in the bottom edge.

I like to use a wooden dowel to push out edges and make sure everything is turned properly.

Grab your fiber fill.

Start filling your pillow, through the opening at the bottom.  I also like to use the wooden dowel to help move the fiber fill around.

Fill the entire pillow, but don’t overstuff.

Pin and hand stitch the opening shut, using your favorite method.

You’re all done!  I cannot wait to see your versions of the Emoji Pillows!  Don’t forget to share your finished projects in the Patterns for Pirates Facebook Group!  (I have this strange feeling that my feed is going to be FULL of poop emojis soon, haha!)  Happy Holidays, friends!

2017 Holiday Freebies :: Slouchy Headwarmer

I. Am. So. Excited.

We are kicking off another year of P4P Holiday Freebies and today is the first of FIVE days of freebies.  I hope you love each and every one of them as much as I do.  We brainstormed pretty hard to find things that were unique, quick to make, and totally giftable for people on your holiday lists.  (And if you’re on your own holiday list, we don’t judge at all!)  Today’s freebie is like four-in-one!  It’s a slouchy headwarmer that can convert into a headband, hat, cowl, and messy bun hat!

Suggested fabrics: Brushed Poly, Rayon/Spandex, (some) Sweater Knits, Cotton Lycras, etc.  The fabric has to have a really good stretch and recovery factor.

Cut square: 20” wide x 20” long.
**The average woman’s head size is 21″ in circumference.  If your head measures smaller/larger than this, it’s easy to adjust accordingly.  I also recommend to add an inch or two if you’re using a thicker cotton/lycra blend or something with a high spandex percentage, as it can be extra tight and end up a little uncomfortable if it’s too tight.

Fold in half, right sides together. Stitch with 1/2” allowance.  Turn right side out.

Fold top right corner to meet bottom left corner.

Grab the outer corner (which was top left corner before we folded in the last step) and have it meet the right bottom corner.

Shown folded with the twist.

Grab the top layer of the four raw edges.

Flip it around the entire headband, so you have a pocket with right sides together.

Stitch around open edge closed, leaving a 2-3” opening for turning.

Pull your headband back through opening, turning it right-sides out.

Blind stitch opening shut.

And now comes the fun part!  This headwarmer can be worn FOUR different ways.  Four!  Amazing, right?  Especially for such a simple sew!  You can…..

…rock it as a headband/earwarmer.

…wear it like a hat.

…throw it on over a messy bun.

…or keep your neck warm, while wearing it like a cowl.

As always, we love when you share what you’ve made with us.  Head over to the Patterns for Pirates Facebook group and show off the fabulous Slouchy Headwarmer that you’ve managed to make from our freebie pattern!  Happy Holidays, friends!

2016 Holiday Freebies: Fleece Mittens Pattern!

The Pirate Crew is here to bring a little more “yo ho ho” into your holiday with some freebies!  Today is the first of three patterns we are releasing, for FREE!  In case you were stumped on Christmas sewing ideas, here is the first of our scrap-busting, super quick, free patterns.

p4p-fleece-mittensp4p-fleece-mittens2 p4p-fleece-mittens3

These mittens are a one-size fits most.  We’ve also provided a cuff and a non-cuff version, so you can mix other fabrics into these easily if you’d like.  The pattern is written for a basic fleece fabric, though some of our testers have had success with sweater knits and other various fabrics.

Grab your free pattern pieces here. If you need help putting the pattern together, pop over to the First Time Users Tips page or ask in our facebook group .

Note: I use my sewing machine for the construction of the mitten body, because the thumb area can be really tricky if you’re using a serger.   When using fleece, it helps to use a walking foot in your machine to help reduce pulling.  It also makes feeding the fleece through your machine a more even process.

Recommended fabrics: Fleece, cuddle/minky, sweatshirt fleece, upcycled sweaters, etc. I suggest washing your fabric before you begin to pre-shrink & help prevent color bleeding in the future.
(Optional cuff) Any knits with at least a 20% stretch.

Supplies needed:

1/3 yard Fleece fabric
(optional cuff) less than 1/4 yard required

Step 1: Assemble your pattern and cut your pieces out.  You will need two sets of mirror images of the main body pieces.

mitten1

Step 2: Lay two mirror images, right sides together.  Using 1/2″ seam allowance, sew around the entire outside of the mitten body.  Make sure to leave the bottom open.

mitten2

Step 3: Clip the corner between the thumb and fingers, making sure not to cut into your stitching, but getting as close as you can to it.  This step is super important, otherwise the mitten will fit really strange in the thumb and it’ll be super uncomfortable.

mitten3

Step 4: [If doing the cuff version, skip to step 6] Turn the opening up 1″ and hem.  (Optional: turn 1/2″ and then another 1/2″ to enclose raw edge.)

mitten4

Step 5: Turn mitten right-side-out.  Repeat with second mitten.

mitten5

Step 6: CUFF VERSION ONLY Complete steps 1-3.  Also cut 2 cuff pieces, one for each mitten.

mitten6

Step 7: Fold your cuff piece, right sides together, meeting the shorter ends together.

mitten7

Step 8: Stitch (using 1/2″ seam allowance) short ends together.

mitten8

Step 9: With wrong sides together, fold the raw edges together to meet each other.

mitten9mitten10

Step 10: On both your mitten body and cuff pieces, mark raw edges into halves.  (The mitten body will be the two seams.  The cuff will be one seam and the halfway point on the opposite side.)

mitten11

Step 11: Slide the cuff over the mitten body, aligning the raw edges and matching the half-marked points.  Note: The cuff is slightly smaller than the mitten body.

mitten12

Step 12: Stretching the cuff only, stitch through all three layers of raw edges.

mitten13

Step 13: Flip cuffs down.  Repeat with other mitten.

mitten14

Step 14: Sit back long enough to admire your handiwork, and then go sew a million more pairs of these comfy mittens!

mitten15

Check out the adorable mittens that our gorgeous testers made!  (And check back with us next week, because we’ve got more freebies coming your way!)

As always, we love when you share what you’ve made with us.  Head over to the Patterns for Pirates Facebook group and show off the fabulous mittens you’ve managed to make from our freebie pattern!

Newest Patterns